首頁 > 資訊動態 > 行業動態

資訊動態

行業動態

常見問題

企業新聞

更多分類

推薦資訊

2025-07-16
水性聚氨酯織物涂層取代水性丙烯酸涂層的理想選擇
2025-06-20
水性聚氨酯膠粘劑：改變傳統膠黏劑趨勢
2025-06-13
深入了解水性聚氨酯及其在紡織領域的應用

產品展示

行業動態

水性聚氨酯膠粘劑在汽車內飾的應用

文字：[大][中][小] 手機頁面二維碼

2018/11/2 瀏覽次數：

一鍵分享

汽車內飾板、頂棚、門板、后備箱內飾、靜電植絨等

汽車內飾水性聚氨酯膠粘劑

水性聚氨酯膠粘劑在汽車內飾中的應用

Application of waterborne polyurethane adhesive in automobile interior decoration

汽車內飾膠是指汽車頂棚、地板、地毯、儀表板、門板等內飾件的粘結，多采用聚氨酯、氯丁等膠粘劑。

Automotive interior adhesive refers to the bonding of automobile ceiling, floor, carpet, dashboard, door panel, and so on.

汽車內飾用泡沫背襯乙烯基塑料、織物與纖維板和其他硬質基材的粘接，過去一直使用溶劑型膠粘劑，而溶劑型膠粘劑正是車內VOC最主要的來源之一，隨著環保法規的健全以及人們環保意識的增強，溶劑型汽車膠粘劑將會逐漸被環保型膠粘劑所取代，尤其是水性汽車內飾膠的推廣應用勢在必行。

The automotive interior is bonded with vinyl plastic, fabric and fiberboard and other hard substrates. Solvent adhesives have been used in the past. Solvent based adhesives are one of the most important sources of VOC in the car. With the improvement of environmental regulations and the increasing awareness of environmental protection, solvent based automotive adhesives will gradually be developed. It is necessary to popularize the environmentally friendly adhesive, especially the waterborne automotive interior adhesive.

與溶劑型聚氨酯膠粘劑相比，水性聚氨酯膠粘劑具有以下特點：

Compared with solvent based polyurethane adhesives, waterborne polyurethane adhesives have the following characteristics:

1、無溶劑，環保，能提供更安全的工作和使用環境。

1, solvent free, environmental protection, can provide safer work and use of the environment.

2、黏度低，且不隨聚合物相對分子質量的改變有明顯差異，因此，可通過提高水性聚氨酯的相對分子質量以提高其內聚強度和初粘強度；而溶劑型膠粘劑的黏度則隨聚合物相對分子質量的增高呈指數關系上升，交聯時易產生凝膠。

2, the viscosity is low and does not vary obviously with the change of the molecular weight of the polymer. Therefore, the relative molecular mass of the waterborne polyurethane can be improved to improve its cohesive strength and initial adhesion strength, while the viscosity of the solvent based adhesive increases exponentially with the increase of the molecular weight of the polymer, and it is easy to produce a coagulant when the polymer is crosslinked. Glue.

3、固含量可高達50%，而大多溶劑型聚氨酯膠粘劑的固含在20%左右，且溶劑型的黏度隨固含量增大而急劇上升，相比之下水性聚氨酯更容易調整配方。

3, the solid content can be as high as 50%, while most solvent polyurethane adhesives are contained in about 20%, and the viscosity of solvent type increases sharply with the increase of solid content, and it is easier to adjust the formula than the water polyurethane.

4、對各種基材如PC，ABS的粘著力與溶劑型相當，但對PP等基材的粘接必須做表面處理。

4, the adhesion of various substrates such as PC and ABS is the same as that of solvent, but the adhesion to PP and other substrates must be treated by surface treatment.

5、干燥過程比溶劑型慢，耗能較大。

5, the drying process is slower than the solvent type, and the energy consumption is larger.

6、投資成本低，無需溶劑回收和防火防爆設施。

6, low investment cost, no solvent recovery and fire and explosion protection facilities.

水性聚氨酯膠粘劑按照不同的應用特點可分為三大類：熱活化粘接、濕法粘接（接觸膠）和冷粘。

Waterborne polyurethane adhesives can be classified into three categories according to their application characteristics: thermal activation bonding, wet bonding (contact rubber) and cold bonding.

熱活化粘接是指膠粘劑在上膠之后，經過干燥，加熱干膠層，使膠層在一定的溫度下產生初粘力，然后再與被粘基材在一定的壓力、時間下復合的一種粘接方式。熱活化粘接是水性聚氨酯膠粘劑最常用的一種應用方式。大多數水性聚氨酯分散體的產品可適用于配置熱活化膠。

Thermal activation bonding is a kind of bonding method, after the adhesive is used, after drying, drying, heating the dry glue layer, making the adhesive layer at a certain temperature to produce the initial adhesive force, and then combined with the sticky substrate in a certain pressure and time. Thermally activated bonding is one of the most common applications of waterborne polyurethane adhesives. Most products of waterborne polyurethane dispersions are suitable for the deployment of heat activated adhesives .

熱活化粘接的過程示意

The process of thermal activation bonding

對于熱活化粘接，結晶速率的快慢直接影響初粘強度的高低和初始耐熱性。一般地，結晶速率越快，初始粘接強度越大，初始耐熱性也越好，粘接達到最終強度的時間也更短。另一方面，相對分子質量的大小又影響到內聚強度和耐熱性，相對分子質量越大，內聚強度高，最終耐熱性好。微信公眾號：nonVOC。

For thermal activation bonding, the rate of crystallization directly affects the initial viscosity strength and initial heat resistance. In general, the faster the crystallization rate, the greater the initial bonding strength, the better the initial heat resistance, and the shorter the time to reach the final strength. On the other hand, the relative molecular mass affects cohesive strength and heat resistance. The greater the molecular weight, the higher cohesive strength and the better heat resistance. WeChat public number: nonVOC.

濕法粘接是指粘接過程不需要熱活化且在水分干燥之前即可進行粘合的一種粘接方式，這類膠粘劑可稱為聚氨酯型的接觸膠。這類粘接方式通常適用于粘接多孔性材料或具有吸水性的材料如織物、海綿、無紡布、木材、紙張等。

Wet bonding is a bonding process that does not need thermal activation and can be bonded before water drying. This kind of adhesive can be called polyurethane type contact adhesive. This type of bonding is usually applied to porous materials or absorbent materials such as fabrics, sponges, non-woven fabrics, wood and paper.

冷粘是指膠粘劑經過干燥后，在一定的時間段以內不需要加熱即可直接進行貼合形成牢固粘接的一種粘接方式。適合這種粘接方式的膠粘劑具有較長的開放時間，通常屬于低結晶型或無定形類的膠粘劑。

Cold sticky means that after drying, the adhesive can be directly bonded to form a bonding method without heating during a certain period of time. Adhesives suitable for this bonding process have a longer opening time and are usually low crystalline or amorphous adhesives.

水性聚氨酯膠粘劑在汽車內飾的應用

Application of waterborne polyurethane adhesives in automobile interior

水性聚氨酯膠粘劑可應用于汽車內飾門板、儀表板、頂棚、座椅、地毯、后置物板、行李箱蓋板、扶手包邊等部件的粘接。

Waterborne polyurethane adhesives can be used in automotive interior door panels, dashboards, roofs, seats, carpets, rear panels, trunk cover plates, armrest edges and other parts .

水性聚氨酯膠粘劑在汽車內飾件粘接的典型應用部件

Application of waterborne polyurethane adhesive in automotive interior trim

采用水性聚氨酯膠粘劑替代溶劑型膠粘劑可顯著降低VOC的排放，同時能保證可靠的粘接質量，盡管水性聚氨酯膠粘劑價格較溶劑型高，但由于其固含量是溶劑型膠水的2~3倍，通過恰當?shù)墓に嚕罱K部件的單位用膠成本可以與溶劑型相當。

The use of waterborne polyurethane adhesive instead of solvent based adhesive can significantly reduce the emission of VOC and ensure reliable bonding quality. Although the price of waterborne polyurethane adhesive is higher than that of solvent type, because its solid content is 2~3 times of solvent type glue, the cost of unit use of the final components can be dissolved by the appropriate process. The dosage form is equivalent.

合肥恒天—懂您的水性聚氨酯定制專家！

聯系我們

合肥恒天新材料科技有限公司

手機：138-0569-8771（何經理）

電話：86-0551-68103252

傳真：86-0551-68103253

郵箱：hengtian_hwh@163.com

地址：安徽省合肥市經濟技術開發區蓬萊路與湯口路交口意大利工業園鑫云泰B座

返回上一步: 打印此頁

上一個：水性聚氨酯地坪漆
下一個：水性聚氨酯膠粘劑是未來發展趨勢！